scanlook-pc-release-notes
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | |||
|
scanlook-pc-release-notes [2020/05/23 10:06] jeff.fagerman [Version 1.0.19X] |
scanlook-pc-release-notes [2020/12/16 07:27] (current) jeff.fagerman [Version 1.0.19X] |
||
|---|---|---|---|
| Line 101: | Line 101: | ||
| - Added "ExtraBytes" for one client (scan angle, local XYZ) to be written to LAS files. Got rid of Alt RGB. | - Added "ExtraBytes" for one client (scan angle, local XYZ) to be written to LAS files. Got rid of Alt RGB. | ||
| - Updating ScanAngle calculation. Trying to make them all relative to nadir. | - Updating ScanAngle calculation. Trying to make them all relative to nadir. | ||
| - | - Applying proximity filter after control/tie corrections. | ||
| - | - If more than 5 returns but only 5 returns allowed by format, using 1 to 4 and then the last return. | ||
| - Hiding sta file if not necessary. | - Hiding sta file if not necessary. | ||
| - Updated control correction to better interpolate over distance independent of event step size. | - Updated control correction to better interpolate over distance independent of event step size. | ||
| - | - Added fore/aft distance filters | ||
| - | - Reading Riegl Model (miniVUX, DL, etc.) directly from SDC. This appears to be undocumented so it may not be perfect for new models). | ||
| - | - Added "ExtraBytes" for CL data per a client request. | ||
| - | - Updated ScanAngle calculation for all current scanners supported for back of car 45 & UAV configurations. | ||
| - Applying spatial proximity filters AFTER applying control/tie corrections. | - Applying spatial proximity filters AFTER applying control/tie corrections. | ||
| - If more than 5 returns but only 5 returns allowed by format, using 1 to 4 and then the last return. | - If more than 5 returns but only 5 returns allowed by format, using 1 to 4 and then the last return. | ||
| Line 125: | Line 119: | ||
| - The Distance calculation in the Graphics tool was incorrect for accumulated, multiple leg measurements. | - The Distance calculation in the Graphics tool was incorrect for accumulated, multiple leg measurements. | ||
| - Added the NCTech 360 iStar camera boresight and colorization. | - Added the NCTech 360 iStar camera boresight and colorization. | ||
| - | - | + | - Added General Options to include Output Options: Distance Break (10) and Time Gap (1). |
| + | - Distance Breaks closes one las file and opens a new one if the distance between lines is greater than the given distance. | ||
| + | - Time Gap does the same thing if the time difference is greater than the given time in seconds. | ||
| + | - Both can be enabled or disabled. | ||
| + | - Added several more scanners. | ||
| + | - Tools menu. Added Image Events to generate metadata file and exif info for UAV imagery. | ||
| + | - Added more event files for RPH (roll pitch heading), Quaternions, and Lat, Long, elev, and more. | ||
| + | - Added minimum speed filter. | ||
| + | - ZF graphics now only show where scanner was recording, not entire trajectory. | ||
| ===== Version 1.0.135 ===== | ===== Version 1.0.135 ===== | ||
scanlook-pc-release-notes.1590253601.txt.gz · Last modified: 2020/05/23 10:06 by jeff.fagerman
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
